Tie Rod and Drag Link Upgrade for the Gladiator JT: Parts, Axle Width, and Torque
Replace the factory tie rod and drag link when one is bent or worn, or when 37s and hard trail use will hit them. On stock parts with 35s and careful driving, Quadratec's take is that factory steering holds up for a reasonable time. Before you buy anything, confirm whether your JT has the standard or wide M210 front axle, since factory parts split on that, and keep the tie rod's stabilizer mount in the plan. This is safety-critical work, so follow the torque-plus-angle numbers and do not reuse fasteners marked one-time.

The two parts do different jobs. The tie rod links the two front knuckles and sets toe. The drag link connects the steering box to the knuckle and sets where the steering wheel sits. Quadratec's catalog sells them separately, and either can be upgraded alone if the other is tight.
This is the Gladiator-specific trap. Stellantis describes third-generation Dana 44 axles across the launch range, but parts catalogs treat the front axle as two widths. Quadratec's JT linkage page splits the inner drag link socket, the right outer tie rod socket, and the stabilizer bracket by standard or wide (M210) axle, each with its own part number.
Aftermarket parts handle this differently, so check each one:
- Synergy describes its drag link as fully adjustable for a variety of axle widths.
- Steer Smarts sells its YETI XD JL tie rod with separate Rubicon (78088001) and non-Rubicon (78076001) part numbers, and that page lists JL fitment only, not JT. It sells a drag link for both, so ask them which tie rod fits your JT before you order.
- TeraFlex lists one tie rod kit for JL and JT at 0-6 inches of lift, with no width split on the page. Confirm with them.
Track width is the best public clue. Jeep's 2024 spec sheet lists a 62.9-inch front track for the Sport and Willys, 64.4 inches for the Rubicon and the Sport with Max Tow, and 65 inches for the Mojave. It doesn't name the axle part, and earlier trims such as the Overland aren't on it, so read your build sheet or ask a dealer with your VIN.
| Part | Construction | Fit notes | Price checked |
|---|---|---|---|
| TeraFlex tie rod 1863910 | HD chromoly | 0-6 inches, left-hand drive. Stabilizer relocation bracket included. | $541.99 |
| TeraFlex drag link 1863920 | 4140 ball and stud, 1045 steel housing | Level 3, 2 to 3 hours per Quadratec. | $467.99 |
| Synergy tie rod 8802-11 | 1.5 x .188-wall chromoly, greasable, pinch bolts | Needs a stabilizer relocation kit to keep the stabilizer. | $550, out of stock when checked |
| Synergy drag link 8800-01 | 1.5 x .250-wall tube, fully welded | Bolts on at the factory location. | $475, out of stock when checked |
| Steer Smarts YETI XD drag link | Assembly with Griffin attenuator | Listed for JL and JT. | From $674.10 |
| Synergy kit 8825-01 | Drag link and tie rod | Relocation kit about $108 extra. | $1,025, out of stock when checked |
If you are on 35s and only one part is suspect, buy that part. If both are worn or you are moving to 37s, the 37-inch guide is where a full linkage upgrade earns its cost. Aluminum tie rods exist, but no source opened here supports recommending them, so they are left out.
Relocation is the follow-on cost people miss. Synergy says its tie rod needs a relocation kit to retain the stabilizer. The kit runs about $108, comes in sizes for a 1-1/2-inch Synergy tie rod or a 1-5/8-inch factory tie rod, and requires drilling the stabilizer bushing sleeve to a 1/2-inch inside diameter. Quadratec rates that kit Level 3. The stabilizer guide covers what a damper can and cannot fix.
High steer is a separate project. Synergy's drag link has an optional flip adapter that moves it to the top of the knuckle. That requires drilling, 3-inch bump stops, the right wheel backspacing, and a track bar relocation bracket. The stock location has no extra requirements. The WAYALIFE JL write-up says a flip and relocation bracket are needed from about 4 inches of lift, so a truck at 2.5 inches can leave this alone. See the track bar guide.
Northridge4x4's factory chart for JL and JT:
| Fastener | Wrench | Torque |
|---|---|---|
| Tie rod end nuts | 21mm | 30 ft-lb + 125 degrees |
| Tie rod adjuster clamp | 13mm | 34 ft-lb |
| Drag link inner nut | 21mm | 29 ft-lb + 125 degrees, do not reuse |
| Drag link outer nut | 21mm | 30 ft-lb + 125 degrees, do not reuse |
| Drag link clamps | 15mm | 34 ft-lb |
| Stabilizer bolt | 18mm | 50 ft-lb, do not reuse |
| Stabilizer nut | 18mm | 55 ft-lb, do not reuse |
The chart says these apply to factory parts. MetalCloak's JL chart, which cites the factory service manual, disagrees: it lists tie rod and outer drag link nuts at 47 ft-lb, the inner drag link nut at 77 ft-lb, and the damper bolt and nut at 59 ft-lb. Neither chart is the JT service manual, so check that before you trust any of these. Aftermarket instructions override them when they list a value. Sources differ on the tie rod clamp: the WAYALIFE write-up gives a 15mm clamp nut at 45 ft-lb, against Northridge's 13mm at 34 ft-lb. Follow your parts' sheet, and verify factory values against a service manual if you are reinstalling factory clamps.
- A factory service manual page for any value above. Northridge4x4's chart is a parts vendor's reference.
- A pitman arm torque for the JT. The chart has none, so none is given here.
- Rough Country's and Apex Chassis's full JT kits. Their pages could not be opened for this guide, so they are not listed. Both appear in search results with lift and axle limits worth reading directly.
Steps
- Park level, chock the rear wheels, loosen the front lugs, and support the frame on stands with the axle secure. Pull the front wheels.
- Measure and write down the center-to-center length of the part you are replacing. Inspect the pitman arm and ball joints while you are there.
- Remove the stabilizer from the tie rod if it is in the way, noting the orientation.
- Remove the nuts and separate the ends with a proper tie rod separator.
- Set the new part to your recorded length, threading both ends evenly.
- Install it and tighten to the numbers above or the maker's sheet. New fasteners where marked. Grease any fittings.
- Refit or relocate the stabilizer and tighten it.
- Refit the wheels, tighten the lugs, and lower the truck.
- Set toe from the tie rod. The JL write-up targets the front of the tires about 1/16 inch closer than the rear, and not more than 1/8.
- Center the wheel from the drag link. Per the JL write-up, loosen the clamp and rotate the adjuster: up turns the wheel left, down turns it right. Tighten and road test.
- Check lock to lock for any contact, get a shop alignment, and recheck everything after your first trail run.
Why it works
- Makers sell these as heavier-duty than factory, with greasable ends and replaceable boots on the Synergy parts. No independent strength test turned up.
- Direct bolt-on at the factory location.
- Can be done as one part at a time.
Trade-offs
- You probably do not need it on 35s with light use and tight factory parts.
- Costs run from about $468 for one part to about $1,133 for a full Synergy kit with relocation.
- Axle width and stabilizer fit both need checking first.
- Alignment is required afterward, and three of the listed parts were out of stock when checked.
Tools required
- floor jack
- jack stands
- 21mm socket
- 13mm and 15mm sockets
- torque wrench with angle gauge
- tie rod separator
- tape measure
- wheel chocks
Parts
| Part | Vendor | Est. price |
|---|---|---|
| TeraFlex HD Forged Drag Link Kit, JL and JT | TeraFlex | ~$468 |
| Synergy Heavy Duty Drag Link, JL and JT | Synergy Manufacturing | ~$475 |
| TeraFlex HD Chromoly Tie Rod Kit, JL and JT, 0-6 inch lift | TeraFlex | ~$542 |
| Synergy HD Chromoly Tie Rod, JL and JT (listed as 8802-11 on the page, 8802-01 in the kit text) | Synergy Manufacturing | ~$550 |
| Steer Smarts YETI XD Draglink Assembly with Griffin attenuator, JL and JT (starting price) | Steer Smarts | ~$674 |
| Synergy HD Steering Kit (drag link and tie rod), JL and JT | Synergy Manufacturing | ~$1025 |
| Synergy steering stabilizer relocation kit, sized to tie rod diameter | Synergy Manufacturing | ~$108 |
Sources
- All-new 2020 Jeep Gladiator press release (Stellantis)
- Crown 68522992AA Drag Link for JL and JT (Quadratec)
- Jeep Gladiator JT Steering Linkage Parts (Quadratec)
- 2020-2026 Gladiator JT Steering Linkage (Quadratec)
- Jeep Bolt Sizes and Torque Specs Chart, JL/JT section (Northridge4x4)
- TeraFlex 1863910 HD Chromoly Tie Rod Kit (Quadratec)
- TeraFlex 1863920 HD Forged Drag Link Kit (Quadratec)
- Synergy HD Chromoly Tie Rod (Quadratec)
- Synergy Heavy Duty Drag Link 8800-01 (Quadratec)
- Synergy HD Steering Kit 8825-01 (Quadratec)
- Synergy Steering Stabilizer Relocation Kit (Quadratec)
- Steer Smarts YETI XD Tie Rod Assembly for JL (Quadratec)
- Basic DIY Jeep JL Wrangler Front End Alignment write-up (WAYALIFE)
- How To Put Bigger Tires On Your Jeep (Quadratec)
- 2024 Jeep Gladiator specifications — Stellantis
Related
- Front Track Bar Upgrade for the Gladiator JT: When You Need One and How to Center the Axle
- Steering Stabilizer Upgrade — Jeep Gladiator JT
- Gladiator steering recalls: what NHTSA lists
- 35" Tire Fitment Guide — Jeep Gladiator JT
- 37s on a Gladiator: what it really takes
- All Jeep Gladiator JT guides & tools
- Browse the full DIY database
Related tools
- Death Wobble Diagnostic — find the cause in eight questions
Written and maintained by an AZ wheeler and driveway wrencher. How we source guides. Always cross-reference your factory service manual — modifications affect vehicle safety and warranty. Work at your own risk. Spot an error? Send a correction and it gets fixed at the source.