Planner
What to buy next, and the best build at any budget
Each rung is the next purchase that matters most per dollar. The dollar mark is what the whole build costs if you go straight to that rung, because an upgrade replaces what it supersedes.
Jeep Cherokee XJ
Trails this rig can doAll Jeep Cherokee XJ guides
- $200Lift · $200
2" Budget Boost (Coil Spacers + Add-a-Leaf)
Coil spacers and an add-a-leaf, about 2 inches.
Replaced by Rough Country 4.5" Short Arm Lift at $2,900
- $600Wheels · $400
Budget Steel and Alloy Wheels for the XJ — 15" and 16" Options
Five 15x8 steel wheels with 3.75-inch backspacing.
Replaced by Budget Steel and Alloy Wheels for the XJ — 15" and 16" Options at $9,900
- $1,600Tires · $1,000
Falken Wildpeak A/T3W
Five 31x10.50R15 all-terrains, the classic fit on a 2-inch lift.
Replaced by Falken Wildpeak A/T3W at $3,250
- $1,900Front bumper · $300
Front Bumper (Winch-Ready)
Steel and winch-ready, with shackle mounts.
- $2,150
- $2,300Tie rod · $150
Heavy Duty Tie Rod
The stock tie rod bends once you add tire.
- $2,900Lift · $800
Rough Country 4.5" Short Arm Lift
Full 4.5-inch kit with coils, rear leaf pack and shocks.
Replaced by Rubicon Express Long Arm Kit at $8,550
- $3,250Tires · $1,350
Falken Wildpeak A/T3W
Five 33x12.50R15. Needs fender trim or high-clearance flares, plus bumpstop extensions.
Replaced by Toyo Open Country M/T at $9,600
- $3,500Drag link · $250
- $3,900Slip yoke eliminator · $400
Slip Yoke Eliminator (SYE) — Hack-N-Tap vs Full Kit
A must-do on a lifted XJ with the NP231.
- $4,950Rear axle · $1,050
Ford 8.8 Explorer Rear Axle Swap (Full Guide)
Swap at 33s and before regearing, or you buy Dana 35 gears twice. These axles often come with a limited slip.
- $5,850Rear bumper · $900
Rear Bumper with Tire Carrier
With a tire carrier: a spare past 31 inches won't fit the factory spot.
- $8,550Lift · $3,500
Rubicon Express Long Arm Kit
Complete long arm kit, the height 35s need.
- $9,200Crossover steering · $650
Crossover Steering (High Steer) Conversion
35s call for one-ton steering up front.
- $9,600Tires · $1,750
Toyo Open Country M/T
Five 35s. Needs a fender cut or flare swap.
Replaced by Tire size guide vs. lift height (XJ) at $19,800
- $9,900Wheels · $700
Budget Steel and Alloy Wheels for the XJ — 15" and 16" Options
Five alloy wheels at the same backspacing.
- $12,150Regear · $2,250
Regearing Cost Overview
Both axles, installed.
- $13,050Front locker · $900
Dana 30 Front Axle Locker Options
The single biggest traction upgrade on the front Dana 30.
- $13,750
- $13,900Engine skid · $150
- $14,300Tank skid · $400
- $19,050Front axle · $4,750
Dana 44 Front Swap (JK Rubicon, WJ HD, Ten Factory)
A stronger front axle before you go past 35s.
- $19,800Tires · $2,500
Tire size guide vs. lift height (XJ)
Estimate for five 37s. Needs SOA height and enters axle-swap territory.
- $19,950Front recovery · $150
- $20,150Rear recovery · $200
- $21,450Winch · $1,300
10,000 lb winch — built XJ standard
The built-XJ standard for steel armor and big tires.
- $21,950Cooling · $500
- $31,950Engine · $10,000
4.6L Stroker Build Overview
The last rung: more power once everything else can take it.
Jeep Wrangler JL
Trails this rig can doCompare lift kitsAll Jeep Wrangler JL guides
- $199Lift · $199
Budget Lift Kit — Spacers and Entry Springs (≤$600)
Rough Country 2-inch kit with N3 shocks, enough for 33s and mild trail. Skip to the mid-tier lift below if 35s are the plan.
Replaced by Mid-Tier Lift Kit — Spring Lift with Geometry Correction ($600–$2,000) at $3,396
- $398Track bar · $199
Front Track Bar Upgrade — Lifted JL Wrangler
Re-centers the front axle after 2 inches or more of lift; the TeraFlex bar is adjustable.
- $847Sliders · $449
Rock Sliders and Rocker Guards
Rock Hard 4x4 Patriot at $449; order the right part for a 2-door JL or a 4-door JLU.
- $1,346Front bumper · $499
Steel Front Bumper — Budget Through Premium Options
Smittybilt XRC Comp comes winch-ready; check for front parking sensors, which a steel bumper can disable.
- $1,796Belly skid · $450
Skid Plate Kit — Engine, Transfer Case, and Fuel Tank
Quadratec aluminum engine and transmission plate at $449.99 for 2021 to 2024 3.6L JLs; add the $349.99 transfer case plate next. Skip or shrink on a Rubicon, which has factory plates.
- $2,696Tie rod · $900
Tie Rod and Drag Link Replacement
Apex KIT115 covers the tie rod and drag link, the steering parts that fail first once you add lift and tire.
- $3,396Lift · $899
Mid-Tier Lift Kit — Spring Lift with Geometry Correction ($600–$2,000)
JKS 2.5-inch with quick-disconnect sway links and geometry correction; clears 35s with minor liner trimming.
Replaced by Expedition and Rock Lift — Long-Arm Full System ($2,000+) at $11,540
- $5,496Tires · $2,100
33s and 35s on the JL: What Fits at What Lift, Rubicon vs Non-Rubicon
Five 35x12.50R17 all-terrains at about $420 each; 33s cost less. The guide lists the lift each size needs by trim.
Replaced by Running 37" Tires on the JL — Rubicon vs Non-Rubicon Fitment at $14,065
- $5,615Front recovery · $119
Recovery Point Hardware — Rated Shackles and D-Ring Mounts for the JL
ARB rated front pair; the factory tow hooks are rated for towing, not for recovery loads.
- $6,915Rear locker · $1,300
Rear Locker Options — Dana 35 and Dana 44
ARB RD244 for the Dana 35 on most Sport and Sahara, compressor extra. Skip on a Rubicon or 2024 Willys, which have a factory rear locker.
- $7,364Winch · $449
Winch Selection for the JL Wrangler — 10,000 lb Minimum
Warn VR EVO 10-S, the 10,000-pound class this guide sets as the minimum for a JL.
- $8,563Rear bumper · $1,199
Rear Bumper with Swing-Out Tire Carrier
Poison Spyder with tire carrier, since a spare past 33 inches outgrows the factory carrier; the Smittybilt at $899 carries up to 35s.
- $11,540Lift · $3,876
Expedition and Rock Lift — Long-Arm Full System ($2,000+)
Rock Krawler 3.5-inch Stage 2, the height 37s need on a non-Rubicon; a 4xe needs a kit confirmed for it.
- $12,440Rear driveshaft · $900
Rear Driveshaft Angle After a JL Lift (No SYE Needed)
Rear driveshaft for lifts past about 2.5 inches: a JL has no slip yoke, so the fix is a double-cardan or CV shaft, and that needs a set pinion angle.
- $12,915Wheels · $475
Wheel Selection for the JL — Steel, Alloy, and Beadlock
Five Pro Comp 17x9 steel wheels at $95 each with 4.5 to 5 inches of backspacing; TPMS sensors are extra.
- $14,565Regear · $1,650
Re-Gearing the JL — 4.56 and 4.88 Ratio Selection
Both axles together: 4.88 for 37s on a Sport or Sahara, and 4.56 at minimum on a Rubicon's 4.10s.
- $14,065Tires · $1,600
Running 37" Tires on the JL — Rubicon vs Non-Rubicon Fitment
Five 37x12.5R17s need the lift and gears above; a Rubicon can fit them with a 1 to 1.5-inch spacer lift instead.
- $15,165Front axle · $1,100
Dana 44 AdvanTEK Front — Service and Upgrade
Spicer chromoly shafts with a FAD delete, since stock shafts bend and the FAD housing breaks past 35s; a Rubicon has no FAD.
Jeep Wrangler JK
Trails this rig can doCompare lift kitsAll Jeep Wrangler JK guides
- $449Sliders · $449
Rock Sliders and Rocker Guards
Smittybilt SRC at $449; buy frame-tied sliders if you will ever jack or winch off them.
- $1,148Lift · $699
Mid-Tier Lift Kit — Spring Lift with Geometry Correction ($600–$2,000)
Teraflex 2.5-inch kit, the guide's proven start; it clears 35s while the factory control arm geometry still works.
Replaced by Expedition Lift Kit — Long-Arm Full System ($2,000+) at $11,313
- $1,337Track bar · $189
Front Track Bar Upgrade — Lifted JK Wrangler
TeraFlex adjustable bar; the lift is not finished until the axle is re-centered and aligned.
- $3,437Tires · $2,100
33s and 35s on the JK: Lift, Backspacing, and Gears for 2-Door and JKU
Five 35x12.50R17 all-terrains at about $420 each on stock or take-off wheels; on 3.73 gears 35s run sluggish, while a Rubicon's 4.10s handle them.
Replaced by Running 37" Tires on the JK — Lift Requirements and Fitment Notes at $11,258
- $3,887Tie rod · $450
Tie Rod Replacement — Heavy Duty Upgrade Options
Synergy chromoly tie rod; the stock tube bends on a hard rock hit, so inspect the drag link too.
- $3,967Front recovery · $80
Recovery Points — D-Ring Mounts, Recovery Hooks, and Frame Tie-Ins
Rated shackles and D-ring mounts; the factory tow hooks are not rated for recovery, and a kinetic rope is the next piece.
- $4,466Belly skid · $499
Skid Plate Kit — Engine, Transfer Case, and Fuel Tank Protection
Teraflex kit for engine, transfer case and fuel tank; skids are year-specific, so match 2007-2011 or 2012-2018.
- $5,366Rear locker · $900
Rear Locker Options for the JK Dana 44
Eaton ELocker, electric with no compressor. Skip on a Rubicon, which has a factory rear locker.
- $7,166Regear · $1,800
Re-Gearing the JK — 4.56, 4.88, and 5.13 Ratios
4.56 on both axles for 35s, about the middle of the guide's $1,200 to $2,400 installed. A Rubicon's 4.10s can wait; go straight to 4.88 if 37s are coming.
Replaced by Re-Gearing the JK — 4.56, 4.88, and 5.13 Ratios at $11,758
- $7,865Front bumper · $699
Premium Steel Front Bumper — Mid and High-End Options ($600–$2,000)
Iron Rock at $699 has a winch plate rated for 12,000 pounds, which a 10,000-pound winch needs. Plan on heavier front springs for the added weight.
- $8,314Winch · $449
Winch Selection — Entry, Mid, and Premium Tiers
Warn VR EVO 10-S, the 10,000-pound class this guide sets for a JK.
- $9,113Rear bumper · $799
Rear Bumper with Swing-Out Tire Carrier
Smittybilt XRC Gen3 carries a 35-inch spare; the factory carrier is built for 31 to 33 inches.
- $11,313Lift · $2,899
Expedition Lift Kit — Long-Arm Full System ($2,000+)
Rock Krawler 3.5-inch RRD, bolt-on and the minimum lift for 37s. A JK needs no SYE; a longer rear driveshaft is the fix.
- $11,758Wheels · $445
Wheel Selection — Steel, Alloy, and Beadlock Options
Five Pro Comp 17x9 steel wheels at $89 each; confirm 4.5 to 4.75 inches of backspacing before mounting 37s.
- $11,758Regear · $1,800
Re-Gearing the JK — 4.56, 4.88, and 5.13 Ratios
Redo at 4.88, the ratio the 37s guide calls required; this replaces the 4.56 set.
- $11,258Tires · $1,600
Running 37" Tires on the JK — Lift Requirements and Fitment Notes
Five 37x12.5R17s; a Rubicon fits them at 3.5 inches with less trimming, and other trims need fender work.
- $11,930Front axle · $672
JK Dana 30 Upgrade Options: Gussets, Sleeves, Chromoly Shafts, or a Dana 44 Swap
Artec C-gussets at about $93 and MetalCloak chromoly shafts at $579; the gussets need a welder. A Rubicon has a Dana 44 front.
- $12,779Front locker · $849
Front Locker Options — Dana 30 and Dana 44
ARB for the Dana 30, only after the rear is locked; the Dana 30 is a weak point under 37s. Skip on a Rubicon, which has a factory front locker.
- $13,128Cooling · $349
Radiator Replacement and Cooling Upgrade (JK Wrangler)
Mishimoto aluminum radiator ends the end-tank cracking failure; the OEM Mopar at $285 is the stock fix.
Jeep Wrangler TJ
Trails this rig can doCompare lift kitsAll Jeep Wrangler TJ guides
- $299Sliders · $299
TJ Rock Sliders — Frame-Mounted Protection for the Rocker Panels
Iron Rock bolt-on, frame-mounted; sliders that bolt only to the body are not worth buying.
- $948Lift · $649
Mid-Tier Lift Kit — 3"–4" Spring Lift ($600–$1,500)
OME 3-inch kit with Nitrocharger shocks, enough for 33s. Skip the spacer kits if 33s are the plan.
Replaced by Long-Arm Lift System — 4.5"+ for Rock Crawling ($2,000+) at $9,446
- $1,108Track bar · $160
Track Bar Replacement — TJ Specifics
Rough Country adjustable bar, the guide's budget pick; it re-centers the axle after a lift.
- $1,483Wheels · $375
Wheel Selection for the TJ — Steel, Alloy, and Beadlock
Five 15x8 Pro Comp steel wheels at $75 each with 3.75 inches of backspacing, so the 33s clear the control arms.
- $3,083Tires · $1,600
33s on the TJ: Lift, Wheels, and Gears
Five 33x10.50R15 all-terrains; 3.73 gears pull 33s but the 3.07s in many automatics do not.
Replaced by Running 35" Tires on the TJ — Lift and Fitment Requirements at $11,046
- $3,682Slip yoke eliminator · $599
SYE Kit for the NP231 Transfer Case — Eliminating Driveshaft Vibration
Tom Wood's SYE plus CV rear driveshaft stops the highway vibration above 2.5 inches of lift. It does not fit a Rubicon's transfer case.
- $3,962Rear locker · $280
Rear Locker for the TJ — Dana 35 and Dana 44
Powertrax lunchbox on the Dana 35, a light-foot fix at 33s. Skip on a Rubicon, which has a factory rear locker.
- $4,252Engine skid · $290
TJ Skid Plates — What the Factory Already Covers, What It Doesn't, and the Tummy Tuck
Skid Row engine and transmission skid; the TJ already has factory transfer case and tank skids, so skip a heavy-duty t-case skid.
- $4,702Front bumper · $450
TJ Steel Front Bumper — Which Style to Buy and Why
Smittybilt XRC stubby with a winch plate; the guide says most TJs never outgrow the $450 tier.
- $5,322Rear bumper · $620
TJ Steel Rear Bumper — Tire Carrier, Recovery Points, and Hitch
Iron Rock with a swing-out carrier, since the factory tailgate hinges fatigue under a spare past a 32.
- $5,442Front recovery · $120
TJ Recovery Points — Rated Anchors for Self-Recovery and Being Pulled
Frame-mount recovery points; the factory front hooks are rated, so this is for a TJ that lost them or needs a rear point.
- $5,771Winch · $329
Winch Selection for the TJ Wrangler
Smittybilt X20 Gen2 at 9,500 pounds, with synthetic rope from the factory.
- $6,371Tie rod · $600
Tie Rod Replacement — Stock and HD Options
RockJock Currectlync, a straight solid bar for 33s on rocks; over 4 inches of lift it needs a dropped pitman arm.
- $6,696Drag link · $325
Drag Link Replacement
Synergy chromoly drag link for 33s to 35s; on the TJ's Y-link steering it carries both front wheels.
- $7,896Rear axle · $1,200
Axle Swap Paths for the TJ (D44, Ford 8.8, D60)
Ford 8.8 swap for the Dana 35, the low end of the guide's $1,200 to $2,200 all-in. A Rubicon already has a Dana 44 rear.
- $9,446Lift · $2,199
Long-Arm Lift System — 4.5"+ for Rock Crawling ($2,000+)
Iron Rock 4.5-inch bolt-on long arm, in the 4 to 5 inches the 35-inch guide calls for.
- $9,796Front axle · $350
Chromoly Shafts and C-Clip Eliminators (TJ)
Dana 30 chromoly front shafts, the minimum the 35-inch guide asks for before 35s.
- $11,246Regear · $1,450
Re-Gearing the TJ — 4.56, 4.88, and 5.13 Ratios
Both axles together: 4.88 for 35s on a manual, and the fitment guide calls for 5.13 on an automatic.
- $11,046Tires · $1,400
Running 35" Tires on the TJ — Lift and Fitment Requirements
Five 35x12.50R15s at about $280 each; plan fender trimming, and check the speedometer after the regear.
Jeep Gladiator JT
Trails this rig can doCompare lift kitsAll Jeep Gladiator JT guides
- $699Lift · $699
Mid-Tier Lift for the Gladiator — 2.5"-3.5" with Geometry Correction ($700–$2,000)
Teraflex 2.5-inch kit with cam bolts and an adjustable track bar; buy a JT-specific kit, and skip spacers if 35s are the plan.
Replaced by Expedition Lift for the Gladiator — Long-Arm System ($2,000+) at $11,955
- $1,148Sliders · $449
Rock Sliders for the Gladiator JT
Rock Hard 4x4 bolt-on at $449; a JL slider will not cover the JT's longer rocker.
- $1,598Belly skid · $450
Skid Plate Kit for the Gladiator JT
Quadratec aluminum engine and transmission plate at $449.99 for the 3.6L; transfer case and fuel tank plates add about $850. A Rubicon already has front axle and transfer case plates.
- $3,698Tires · $2,100
35" Tire Fitment Guide — Jeep Gladiator JT
Five 35x12.50R17 all-terrains at about $420 each; they clear at 2.5 inches of lift, though full lock may still touch.
Replaced by 37s on a Gladiator: what it really takes at $12,105
- $4,197Front bumper · $499
Aftermarket Front Bumper for the Jeep Gladiator JT
Rough Country at about $499; check for front parking sensors and a forward camera, which budget bumpers often skip.
- $4,646Winch · $449
Winch for the Gladiator JT — 10,000 lb Minimum
Warn VR EVO 10-S; 10,000 pounds is the minimum for a JT's 5,400 to 6,200 pound GVWR.
- $4,786Steering stabilizer · $140
Steering Stabilizer Upgrade — Jeep Gladiator JT
Bilstein stabilizer for 35s; it damps shimmy but does not fix worn steering parts.
- $5,586Tie rod · $800
Tie Rod and Drag Link Upgrade for the Gladiator JT: Parts, Axle Width, and Torque
Heavy-duty tie rod and drag link for 35s and up; fix worn steering parts before blaming the stabilizer.
- $5,606Rear recovery · $20
Tow Hook and Recovery Point Upgrade — Jeep Gladiator JT
A receiver D-ring mount at about $20; the steel front bumper already carries rated tabs.
- $7,206Regear · $1,600
Re-Gearing the Gladiator JT — 4.56 and 4.88 Ratios
Both Dana 44s together, 4.56 for 35s, at the 35-inch guide's $1,200 to $2,000 shop price. A Rubicon's 4.10s can wait.
Replaced by Re-Gearing the Gladiator JT — 4.56 and 4.88 Ratios at $11,955
- $8,306Rear locker · $1,100
Rear Locker for the Gladiator JT — Dana 44 Options
Eaton ELocker needs no compressor. Skip on a Rubicon, Mojave or 2024 Willys, which have a factory rear locker.
- $8,655Rear bumper · $349
Aftermarket Rear Bumper for the Jeep Gladiator JT
Rough Country with a 2-inch hitch; the JT spare lives under the bed, so there is no carrier to buy.
- $11,955Lift · $3,999
Expedition Lift for the Gladiator — Long-Arm System ($2,000+)
Rock Krawler 3.5-inch mid-arm, the lift 37s need; it must be a JT-specific kit, not a JL kit.
- $11,955Regear · $1,600
Re-Gearing the Gladiator JT — 4.56 and 4.88 Ratios
Redo at 4.88 for 37s, which the 37s guide calls mandatory; this replaces the 4.56 set.
- $12,105Tires · $2,250
37s on a Gladiator: what it really takes
Five 37x12.50R17 all-terrains at about $450 each; expect fender trimming, and budget about $235 for a tire-size programmer.
Toyota 4Runner
Trails this rig can doAll Toyota 4Runner guides
- $549Lift · $549
Budget Lift Kit — Bilstein 5100 and Spacers (≤$600)
Bilstein 5100 set for non-KDSS trucks; a Trail or TRD Pro with KDSS needs KDSS-valved shocks instead.
Replaced by Mid-Tier Lift with UCAs — 2.5"–3" Lift ($1,000–$2,500) at $5,898
- $1,899Tires · $1,350
Budget All-Terrain — Big Capability Per Dollar
Five 285/70R17 value all-terrains mounted, within the guide's $1,200 to $1,500; the size clears with a mild lift and light trimming.
Replaced by 35s on the 5th Gen 4Runner: Lift, Body Mounts, Cutting, and Gears at $14,521
- $2,599Sliders · $700
Rock Sliders and Frame Rails for the 5th Gen 4Runner
Frame-mounted sliders, not N-Fab nerf bars; the guide lists CBI, Shrockworks and Metal Tech.
- $3,349Belly skid · $750
Skid Plate Kit for the 5th Gen 4Runner
A full kit adds transfer case and fuel tank cover. Trail and TRD Pro already have thin factory engine and front skids.
- $4,649Front bumper · $1,300
Steel Front Bumper for the 5th Gen 4Runner
CBI at about $1,299; confirm the winch plate and parking sensor fit for your year.
- $5,098Winch · $449
Winch for the 4Runner — 10,000 lb Minimum
Warn VR EVO 10-S on synthetic rope; it needs the steel bumper's winch plate first.
- $5,148Rear recovery · $50
Recovery Points for the 4Runner — Frame-Mounted D-Rings and Shackle Mounts
A receiver hitch D-ring mount at about $50; the steel bumper supplies the front points.
- $5,898Lift · $1,299
Mid-Tier Lift with UCAs — 2.5"–3" Lift ($1,000–$2,500)
Icon Stage 2 with upper control arms, which a lift past 2 inches needs; KDSS trucks must order the KDSS-valved version.
Replaced by Expedition Lift — Long-Travel and Dual Remote Reservoir ($2,500+) at $13,521
- $6,773Wheels · $875
Wheel Selection for the 5th Gen 4Runner
Five Method 701 Trail 17x8.5 at $175 each, about 4.75 to 5 inches of backspacing for 33s.
- $8,773Regear · $2,000
Re-Gearing the 5th Gen 4Runner — Ratios for 33s and 35s
Both axles together: 4.88 for 33s and 5.29 for 35s; the front clamshell needs a shop that has set one.
- $9,472Rear locker · $699
Rear Locker for the 5th Gen 4Runner — ARB, Eaton, and the Factory Locker
Eaton ELocker on the 8.9-inch rear, no compressor needed. Skip on a Trail, TRD Off-Road or TRD Pro, which have a factory rear locker.
- $10,371Rear bumper · $899
Rear Bumper and Swing-Out Tire Carrier for the 4Runner
CBI at $899 buys departure angle and rated points; a swing-out carrier costs more.
- $12,321Front locker · $1,950
Front Locker — Selectable Traction Up Front
ARB front locker with compressor and setup, mid-range of the guide's $1,700 to $2,200 DIY; order the part number after the regear.
- $13,521Lift · $2,499
Expedition Lift — Long-Travel and Dual Remote Reservoir ($2,500+)
Icon Stage 3 remote reservoir coilovers; KDSS trucks need the compatible version, and long-travel kits require a KDSS delete.
- $14,521Tires · $2,350
35s on the 5th Gen 4Runner: Lift, Body Mounts, Cutting, and Gears
Five 35s at about $420 each plus about $250 for body mount work, after the gears and the lift. The guide lists every cut; this is where a 4Runner gets hard.
Toyota Tacoma
Trails this rig can doAll Toyota Tacoma guides
- $638Lift · $638
Budget Lift Kit — Bilstein 6112 Front and Rear Add-a-Leaf
Bilstein 6112 fronts at $449 plus an SCS add-a-leaf at $189, good for 1.5 to 2 inches.
Replaced by Mid-Tier Lift with Upper Control Arms ($600–$2,000) at $5,447
- $1,713Tires · $1,075
Running 33" Tires on the Tacoma — 285/75R16 and 295/70R17 Fitment
Five Falken Wildpeak 285/75R16 at about $215 each; at 2 inches trim the mud flap bracket, and 2.5 inches clears untouched.
Replaced by 35s on the Tacoma: Lift, Cab Mount, Cutting, and Gears for 2nd and 3rd Gen at $13,872
- $2,412Sliders · $699
Rock Sliders and Frame Rails for the Tacoma
CBI frame-mounted sliders at $699; a nerf step is not a substitute.
- $3,111Belly skid · $699
Skid Plate Kit for the Tacoma — Engine, Transfer Case, and Fuel Tank
CBI kit covers oil pan, transmission, transfer case and fuel tank; check for crossmember gussets.
- $4,061Front bumper · $950
Hybrid / Low-Profile Front Bumper
A steel hybrid adds about 120 pounds, so set the 6112 collars for it; on 2018 and newer trucks, confirm it clears the Safety Sense radar.
- $4,611Winch · $550
Budget Synthetic-Line Winch
Smittybilt X2O Gen2 10K on synthetic line; it needs the bumper's frame-tied winch mount.
- $4,786Rear recovery · $175
Recovery Points for the Tacoma — Rated Hooks, Not the Tow Loop
A rated frame-mount point at the rear, since almost no Tacoma has one; never use a tow ball.
- $5,447Lift · $1,299
Mid-Tier Lift with Upper Control Arms ($600–$2,000)
Icon Stage 2 with upper control arms; a lift past 2 inches runs out of caster without them, and the alignment is part of the cost.
Replaced by Long-Travel Suspension — Expedition and Desert Build ($2,500+) at $12,647
- $7,947Regear · $2,500
Regearing the Tacoma for Larger Tires — 4.88 / 5.29 (3rd Gen)
Low end of the guide's $2,500 to $4,000 shop price; 4.88 for 33s and 5.29 for 35s, front and rear matched.
- $9,597Rear locker · $1,650
Rear Locker for the Tacoma — ARB and Eaton Options
ARB at $1,250 plus a $400 compressor, an estimate. Skip on a TRD Off-Road, TRD Pro or 2022 and newer Trail Edition, which have a factory locker.
- $10,747Rear bumper · $1,150
Rear Bumper and Trailer Hitch Integration for the Tacoma
CBI bare bumper at about $1,150; a swing-out carrier adds $400 to $900 and makes the leaf pack upgrade required.
- $12,647Lift · $3,199
Long-Travel Suspension — Expedition and Desert Build ($2,500+)
Total Chaos long-travel kit with 12 to 14 inches of front travel; a shop install, and a rear coilover conversion adds $2,000 to $4,000.
- $13,872Tires · $2,300
35s on the Tacoma: Lift, Cab Mount, Cutting, and Gears for 2nd and 3rd Gen
Five 35s at about $420 each plus about $200 in cab mount parts and welding you quote locally. Sources disagree on the lift, and the guide shows the range.
Prices are typical parts costs from each linked guide, and tire and wheel rungs are priced as a set of five. Labor, tax and shipping aren't included. Written and maintained by an AZ wheeler and driveway wrencher. Last reviewed .