DIY Jeep Cargo Drawers: Plans for the TJ, XJ, JK and JL
A plywood drawer system is the most useful interior project on a trail rig, and on some Jeeps it is the only real option. The hard part is not the woodworking. It is that a 2-door JL and a JL Unlimited need different boxes, a factory subwoofer can take up the space you planned on, and the floor under an XJ hides a plastic fuel tank. Here is how the kits rate, then four builds with cut lists and full instructions.

Buy if you have a JL Unlimited, want it installed this weekend, and have no reason to change the layout. Build if you have an XJ, a 2-door, a factory subwoofer, or a specific fridge. Most owners should start with 6-inch side-by-side drawers: they stay about 9 inches tall, hold most recovery gear and tools, and leave room above. Choose 9-inch drawers if you rarely stack on top. Choose the half-depth version with a hinged rear bay if you carry long gear you rarely need. Whatever you build, bolt it down with real hardware, because this box becomes a projectile in a crash.
Measure your Jeep first
Jeep's published figures are measured at the trim and they do not agree with owners' tape measures, and owners do not agree with each other. Use the table to choose a starting box, then build a cardboard mockup in your own Jeep before cutting anything. Width has to clear two things: the wheel wells and the opening you carry it through, unless you plan to assemble it inside.
| Rig | Seat | Start width | Start depth | Drawer interior, side by side | What the numbers come from |
|---|---|---|---|---|---|
| JL Unlimited | Up | 40 | 32 | 16 5/8 x 29 | 45 in between wells, 41.1 in gate opening, official. 34.5 in seat base to gate, owner |
| JL Unlimited 4xe | Up | 40 | 28 | 16 5/8 x 25 | About 29.5 to 30 in seat to door at sill height, owner, 2024 |
| JL 2-door | Out | 40 | 36 | 16 5/8 x 33 | 44 to 48 in deep with the seat out, owners disagree on width |
| JK Unlimited | Up | 40 | 28 | 16 5/8 x 25 | 44.7 in between wells, official. Front Runner kit is 42.8 x 28.4 x 10.6, a useful reference |
| JK 2-door | Out | 37 1/2 | 28 | 15 3/8 x 25 | 37.5 to 42 in wide, by owner. 12 to 18 in deep with the seat up, too short to build for |
| LJ (TJ Unlimited) | Up | 34 | 20 | 13 5/8 x 17 | Tuffy 131-01 is 34 x 20 1/4 x 13 behind the LJ seat |
| TJ | Out | 34 | 30 | 13 5/8 x 27 | About 36 x 36 in floor, owner. Tuffy 058-01 is 35 3/8 x 30 x 8 |
| XJ | Up | 41 | 29 | 17 1/8 x 25 | 43 in between wells, 34 1/2 in long at the floor, owner. 48 x 32.75 in opening, owner |
Depth is overall, including the 3/4 in drawer face. The interior column assumes two drawers and 3/4 in slides. Treat all of these as starting points for a mockup, not as final dimensions.
Traps by platform
- TJ and LJ. A TJ has to lose the rear seat for most drawers. The LJ is the exception: the Tuffy 131-01 goes behind the LJ seat on factory holes, but the TJ needs the seat out. Some door frames have a 1 in lip that calls for a riser. A box near 36 in wide is tight: owners report 34.25 to 34.5 in with brackets.
- XJ. Do not drill blind. One owner's floor mount ran into frame rails, the plastic fuel tank, filler hoses and shackle mounts. The spare is also inside: a full-width box means moving it, and owners report needing about 1.5 in of floor clearance for the latch.
- JK. On a 2-door, plan on the seat out. On an Unlimited, an owner measured 43 in between fenders but 36.5 in at the factory sub. One owner found the floor anchors are M6x1.0 on a 2014 JKU, which is small for this job.
- JL 2-door. We found no reliable seat-up depth, and owners describe it as very short. Build for seat-out, or look at the Goose Gear 2-door plate as a reference.
- JL 4xe. The battery sits under the rear seat, and cargo volume drops to 67.4 cu ft folded. Owners describe the folded seat as a ledge about 7 in above the floor. Kit makers disagree on fit: Tuffy excludes it, while Rugged Ridge lists it.
- JL 392. Goose Gear sells a separate 392 plate, with sub only, so do not assume a standard JLU plan transfers. Mock it up.
Subwoofers: check before you design
Look under the cargo floor panel before you buy a single sheet of plywood. Whether you have a sub depends on the audio package, not only the trim.
| Rig | Where it is | What it means for your box |
|---|---|---|
| JL (Alpine 9-speaker) | A 10 in sub in the cargo floor, per owners. Exact exterior size not confirmed. 2-door owners describe a shallow floor tub | It decides your layout. Rough Country 99030 excludes it and SquadBox J257997 is not compatible. Goose makes a narrower module on the sub side |
| JK Unlimited | Takes owners down to 36.5 in wide at the sub. Location varies by year | ARB needs a JKBRKT1 bracket on 2007-09 rigs with the sub. Front Runner says its 2011+ slide works with the sub. Measure your own |
| TJ | In the center console, not the cargo area | No conflict with a drawer box |
| XJ | No factory cargo sub found. The Infinity amp is reported under the rear seat | Check for an aftermarket box from a previous owner |
Three ways to deal with a JL or JK sub
- Build around it. Narrow the drawer on the sub side, or raise the box on battens until it clears, and cut the base panel. The half-depth build below handles this best, because the hidden bay has no fixed bottom.
- Relocate it. On an Unlimited JK, under-seat subs such as the Alpine PWE-S8-WRA replace it, though owners report seat vibration.
- Remove it. JK owners report about 20 minutes with star bolts, and on a JL the connector is behind the passenger-side plastics. Removing only the sub is reported fine by one owner. Do not bypass the factory amp to do it, because it holds the tuning and volume control. Keep the parts: it is reversible.
Should you buy instead? Kits rated
We rated these from owner reviews, forum reports and listings, and we did not test them. Scores are out of 5, and n/r means we could not rate it. Read the evidence column first: durability evidence for most of these is thin, and we found no product-specific reports on dust. Prices were checked October 30, 2026. These links go to the pages we read, and none are affiliate links.
JL
| Kit | Price | Owner | Value | Durability | Fit | Sub? | Evidence |
|---|---|---|---|---|---|---|---|
| Goose Gear plate and modules | $895 for the 2-door plate, modules extra | 4 | 2 | 3 | 4 | With-sub versions | Thin. Owners call it well built and complain about price and lead time |
| American Adventure Lab M.A.S.S. | $299.95 to $369.95 platform, drawers extra | 4 | 3 | 4 | 4 JLU, 2 two-door | Not stated | Thin to moderate, forums only. Solid and smooth, heavier than expected |
| ARB Roller Drawer RDK5013020 | $1,981.90 | 3.5 | 2 | 3 | 4 | This SKU is for sub rigs | Thin. 1 review. One owner: the floor pulls open with the drawer locked |
| Rugged Ridge 13551.42 | $899.99 | 2.5 | 3 | 3 | 3 | Not documented | Very thin. 3.0 from 2 reviews |
| Smittybilt 2763 (also JK) | Discontinued at ExtremeTerrain | 4 | n/r | 3 | 3 | Not stated | Largest count we found: 4.6 from 72, text not read. Rattle complaints |
| Tuffy deck enclosure 345-01 / 351-01 | $549 | 3.5 | 3 | 3 | 3 | 351-01 is the sub version | Moderate count, 3.6 from 23. Low-star reviews not visible. A lidded deck, not a drawer. No 4xe |
| Rough Country 99030 | $549.95 | 4 | 4 | n/r | 2 | Excludes the sub | Very thin. 4.8 from 4 reviews, no text |
| TACTIK box (also JK) | About $450 | 3 | 3 | 2 | 3 | Not stated | Thin. Drawer rocks and taps, thin metal, needs drilling |
| Hooke Road drawer and fridge mount (also JK) | $499.99, vendor post | n/r | 4 | n/r | 3 | Vendor says sides can swap | No independent reviews |
| DECKED SUV drawer (also JK) | Not published | n/r | n/r | n/r | n/r | Not stated | Announced October 27, 2026. Door count not stated |
JK
| Kit | Price | Owner | Value | Durability | Fit | Evidence |
|---|---|---|---|---|---|---|
| Front Runner SSJW002 (JKU) | $1,508 | n/r | 3 | n/r | 3 | Clear specs: 84 lb, 250 lb drawer rating. No owner reviews found |
| ARB 5011010 (Unlimited) | $2,493.80 plus $100 surcharge, out of stock | n/r | 2 | n/r | 4 | Vehicle-specific. 2007-09 rigs with a sub need a bracket |
| Goose Gear JK/JKU modules | Not confirmed | 4 | 2 | 3 | 4 | Thin. Same builder as the JL line |
| Tuffy Security Drawer #140 | No longer available | n/r | n/r | n/r | n/r | Worked with the factory sub on 4-doors. Used only |
TJ and LJ
| Kit | Price | Owner | Value | Durability | Fit | Evidence |
|---|---|---|---|---|---|---|
| Tuffy 131-01 | $749 | 4 | 3 | 4 | 4 LJ, 2 TJ | Very thin on this SKU, 1 review. The only behind-seat LJ option we found |
| Tuffy 058-01 | $749 | 4 | 3 | 3 | 3 | Very thin. Replaces the seat. Older Tuffy owners report rattles and water leaks, along with praise for strength |
XJ
We found no current commercial drawer kit. The JCR XJ Cubby Mate is no longer available, and Tuffy's 130-01 underseat drawer is discontinued. If you own an XJ, the rest of this article is your plan. One owner who adapted a Tuffy drawer had two slide screws pull through and replaced them all with M6 grade 10.9 flange bolts. Build that lesson in from the start.
Between the kit and a full build, a forum seller offers CNC-cut kits for $270 to $390, by the seller's own description. One owner estimated a DIY build at about two-thirds of the cost of a Goose Gear setup, tools included.
Choose your layout
| Build | Overall height | Best for | Gives up |
|---|---|---|---|
| A. 6-inch double | 9 in | Tools, recovery gear, spares. A flat deck that takes a fridge or gear on top | Tall items |
| B. 9-inch double | 12 in | Cook kits, bottles, bulky gear | Space above. A top-mounted fridge gets tall |
| C. Fridge slide, beside a drawer or on top | 9 to 12 in plus the fridge | Trips where the fridge earns its place | Half your drawer space, or a higher center of gravity |
| D. Half-depth with a hinged bay | 9 in | Recovery boards, straps, a jack, things you rarely need. Rigs with a floor sub | Drawer depth, and a long reach into the bay |
"Double" here means side by side. You can stack two 6-inch drawers instead, at about 16 in overall, but that takes more height than most Jeeps can spare with the seat up, and it puts weight higher. Side by side is the better default.
Materials and hardware
Slides: where to spend the money
Slides decide whether this project works after a year of washboard. Use heavy-duty slides that lock at both ends: closed, so the drawer stays in on a climb, and fully extended, so it does not roll back into you on a slope. ARB advertises an anti roll-back lock for the same reason. Amazon now lists 3 in wide, 2.5 mm steel locking slides that cost far less than the industrial brands, and they are what we plan these builds around.
| Amazon slide (1 pair) | Listed price | Reviews | Thickness | Lengths | Notes |
|---|---|---|---|---|---|
| SHUHANG 76mm with lock | $92.00 as listed | 4.5 from 69 | 19/25 in per side | 12 to 40 in by 2s, then 44 to 60 | Our default, because it comes in every length here. Locks only fully closed and fully extended. Title says 500 lb, bullets say 490 lb. Screw info conflicts, so buy M6 |
| SLIDEWAY 76mm locking | $84.99 for 24 in | 4.6 from 133 | 0.76 in | 16 to 60 in range | Most reviews. 2.5 mm Q235 steel, zinc plated, 24 M6 screws included. Maker says shorter slides carry more |
| VEVOR 24 in single lock | $46.90 | 4.5 from 67 | 0.77 in | 24 in here. Check others | Cheapest. Pair lists 13.2 lb, 16 screws. Another VEVOR 24 in listing says 250 lb, so check the listing you buy |
Prices and ratings read from Amazon on October 30, 2026. Links open a search because listings change. We have not tested these slides. Every rating above is the seller's claim, at a length they mostly do not state. Plan on your plywood and M6 screws being the real limit, and in our judgment keep each drawer under about 100 lb.
Check two things when they arrive, before you cut a drawer face. First, measure the thickness: the cut lists assume 3/4 in per side, and these run about 0.76 in, which is close enough. Second, find the lock lever. It sits on the slide near the front, so a full-overlay face can hide it. You will notch the face to reach it (step 10).
If you would rather buy industrial slides
| Slide | Rating | Locks | Notes |
|---|---|---|---|
| Fulterer 5600L / 5609L | 250 lb | In and out | 30, 32, 34 in seen. Confirm shorter lengths |
| Accuride 9308E | Accuride rates the related 9301E up to 600 lb | In and out, front lever | About EUR 196 for a 32 in at one reseller |
| Accuride 3832 | 100 lb | Hold-in | Light loads only. Reasonable for half-depth drawers |
Skip the Fulterer FR5000 for this: it is rated at 100 lb and sold as medium duty.
Plywood
- Use 1/2 in Baltic birch for boxes and 3/4 in for the deck and divider. Goose Gear uses 11-ply Baltic birch dovetail boxes. True Baltic birch has been reported as hard to find, so a void-free cabinet-grade sheet is a fair substitute.
- Do not trust the glue to keep it dry. Sources conflict on whether Baltic birch is water-resistant, so seal it. One builder used spar varnish on 1/2 in birch.
- Skip solid boards. An XJ owner reports solid 1x12 cracks and splits.
Fasteners and latches
- Bolt the slides. Use M6 machine screws into T-nuts or threaded inserts, not wood screws. That is the failure the XJ owner above had.
- Latches. Southco's 64-series paddle latches come non-locking (64-21-10) and key-locking (64-22-10) in stainless. Locking slides already hold the drawer shut, so a latch is mainly for security. Recess it in the face so the face stays flat.
- Quiet it. Owners of steel drawers fix rattle with foam weatherstrip and nylon spacers. Add both from day one.
Build A: 6-inch double drawer
This is the default. The cut list is for a reference box 40 in wide and 28 in deep overall, which suits a JL Unlimited 4xe or a JK Unlimited, using 26 in slides. Each drawer's inside measures 16 5/8 x 25 x 5 1/2 in.
| Part | Plywood | Qty | Size (in) |
|---|---|---|---|
| Bottom | 1/2 | 1 | 40 x 27 1/4 |
| Top deck | 3/4 | 1 | 40 x 27 1/4 |
| Outer sides | 1/2 | 2 | 27 1/4 x 7 |
| Center divider | 3/4 | 1 | 26 3/4 x 7 |
| Back | 1/2 | 1 | 39 x 7 |
| Floor battens | 3/4 | 3 | 27 1/4 x 1 1/2 |
| Drawer bottoms | 1/2 | 2 | 17 5/8 x 26 |
| Drawer sides | 1/2 | 4 | 26 x 5 1/2 |
| Drawer ends | 1/2 | 4 | 16 5/8 x 5 1/2 |
| Drawer faces | 3/4 | 2 | 19 7/8 x 8 |
About 25 sq ft of 1/2 in and 12 sq ft of 3/4 in. Plywood alone comes to about 70 lb by our arithmetic, assuming about 55 lb and 71.5 lb per 4x8 sheet, figures we could not confirm from a strong source, so weigh your own. We found no measured DIY build to compare. Slides add more: a VEVOR 24 in pair lists 13.2 lb, so two pairs add about 26 lb. For scale, the ARB RDRF790 is 105.8 lb and the Front Runner JKU kit is about 84 lb.
Build B: 9-inch double drawer
Same footprint with 3 in more height, for a 12 in stack. Each drawer's inside measures 16 5/8 x 25 x 8 1/2 in. Check it against your seat back and gate before committing. In a TJ, owners measure wheel wells about 11 to 12.5 in tall, so this deck ends up about level with the top of them. On a soft-top TJ, a retailer Q&A on the 13 in Tuffy 131-01 says the top folds down, but not completely, so expect the same from a tall deck.
| Part | Plywood | Qty | Size (in) |
|---|---|---|---|
| Bottom | 1/2 | 1 | 40 x 27 1/4 |
| Top deck | 3/4 | 1 | 40 x 27 1/4 |
| Outer sides | 1/2 | 2 | 27 1/4 x 10 |
| Center divider | 3/4 | 1 | 26 3/4 x 10 |
| Back | 1/2 | 1 | 39 x 10 |
| Floor battens | 3/4 | 3 | 27 1/4 x 1 1/2 |
| Drawer bottoms | 1/2 | 2 | 17 5/8 x 26 |
| Drawer sides | 1/2 | 4 | 26 x 8 1/2 |
| Drawer ends | 1/2 | 4 | 16 5/8 x 8 1/2 |
| Drawer faces | 3/4 | 2 | 19 7/8 x 11 |
About 30.5 sq ft of 1/2 in and 13.3 sq ft of 3/4 in, or about 82 lb of plywood by the same arithmetic.
Changing the size for your rig
| Dimension | Formula |
|---|---|
| Carcass depth | Overall depth minus 3/4 in (the drawer face) |
| Slide length | Carcass depth minus 1/2 in, rounded down to a size you can buy |
| Drawer opening height | Drawer height plus 1 in |
| Drawer opening width, double | (Overall width minus 1 3/4 in) divided by 2 |
| Drawer box width | Opening width minus twice the slide thickness |
| Drawer sides | Slide length x (drawer height minus 1/2 in) |
| Drawer ends | (Box width minus 1 in) x (drawer height minus 1/2 in) |
| Drawer face | (Half the overall width minus 1/8 in) x (opening height plus 1 in) |
| Overall height | Drawer height plus 3 in, with 3/4 in battens |
Build C: with a fridge slide, or without
If you only pull the fridge out at camp, a slide may not be worth losing the space. If you open it several times a day, it is. Choose the slide first, because it sets your depth: the Dometic CFX3-SLD3545 is 18.94 W x 3.35 H x 28.93 D in and rated for 220 lb.
| Fridge | Size (in) | Empty | Most it could weigh full* | Slide check |
|---|---|---|---|---|
| Dometic CFX3 45 | 27.3 x 15.7 x 18.7 | 41 lb | About 142 lb | Under Dometic 220 lb |
| Dometic CFX3 55IM | 28.35 x 17.91 x 18.90 | 47 lb | About 164 lb | Under Dometic 220 lb |
| ICECO JP42 | 28.4 x 16.4 x 17.6 | 45 lb | About 137 lb | Under ARB 10900021, 176.4 lb, with less margin |
| ICECO VL45 | 27.4 x 15.8 x 19.2 | 50.6 lb | About 150 lb | Same, close to the ARB rating |
*Our arithmetic: capacity in liters as water at 2.2 lb per liter, plus the empty weight. Real loads run lower.
Beside a drawer
This keeps the weight low, and it is our first choice where the width allows. It takes a 23 in bay: 18.94 in for the slide plus clearance on each side. Dometic's manual calls for about 50 mm of ventilation clearance on all sides. The cut list is for 40 in wide and 30 in deep, with a 17 in drawer module and 28 in slides. The drawer's inside measures 13 1/2 x 27 x 8 1/2 in.
| Part | Plywood | Qty | Size (in) |
|---|---|---|---|
| Module bottom | 1/2 | 1 | 17 x 29 1/4 |
| Module top | 3/4 | 1 | 17 x 29 1/4 |
| Module sides | 1/2 | 2 | 29 1/4 x 10 |
| Module back | 1/2 | 1 | 16 x 10 |
| Module battens | 3/4 | 2 | 29 1/4 x 1 1/2 |
| Fridge floor plate | 3/4 | 1 | 23 x 29 1/4 |
| Drawer bottom | 1/2 | 1 | 14 1/2 x 28 |
| Drawer sides | 1/2 | 2 | 28 x 8 1/2 |
| Drawer ends | 1/2 | 2 | 13 1/2 x 8 1/2 |
| Drawer face | 3/4 | 1 | 16 3/4 x 11 |
About 50 lb of plywood by our arithmetic, before the slide. Dometic lists its slide at 31.3 lb.
On top of the deck
This keeps both drawers. A CFX3 45 on its slide on a 6-inch deck tops out at about 31 in, and on a 9-inch deck at about 34 in. Bolt the slide through the deck into a plate below, or into the battens, and do not rely on deck screws. Then check the opening:
| Rig | Fits beside a drawer? | 6-inch deck, 31 in top | 9-inch deck, 34 in top |
|---|---|---|---|
| JL Unlimited | Yes, with a 17 in drawer | Fits a 36 in gate opening | Fits, under 2 in spare |
| JL Unlimited 4xe | Slide is too deep with the seat up, by about 1 in at our 28 in box | Same depth limit | Same depth limit |
| JL 2-door, seat out | Yes | Fits. With the seat in, an owner reports a CFX3 45 slide barely fits | Fits |
| JK Unlimited | Only if your box can reach about 30 in | Fits a 37 in gate opening | Fits |
| JK 2-door, seat out | Tight, a 14 in drawer | Fits | Fits |
| TJ, seat out | No, too narrow at 34 in | Check your top: owners measure about 44 in to a hardtop | Check your top |
| XJ | Yes, if the spare moves | Fits a 32.75 in opening by under 2 in | No |
Power and tie-down
- Use the fuse printed on your fridge's plug label. Dometic's support page says the value varies.
- One retailer recommends 12 AWG for a DIY circuit to a CFX3 45. Size your run with the wire gauge calculator, and fuse it to protect the wire.
- Strap the fridge to the slide. Dometic's slide includes four straps. A loose fridge is one of the heavier objects in the Jeep.
Build D: half-depth drawers and a hinged rear bay
The drawers take the half nearest the tailgate, and a hinged lid covers the half nearest the seat. You get quick access at the back and a protected bay for gear you rarely touch, such as traction boards, a jack, straps and a compressor. It also suits a rig with a floor sub, since the bay has no fixed bottom and can sit over it. Measure the sub's height first: the bay has 8 1/4 in under the lid.
The cut list is for 40 in wide and 30 in deep overall, with 6-inch drawers on 14 in slides. Each drawer's inside measures 16 5/8 x 13 x 5 1/2 in. The bay inside measures about 39 x 13 3/4 x 8 1/4 in.
| Part | Plywood | Qty | Size (in) |
|---|---|---|---|
| Bottom under drawers | 1/2 | 1 | 40 x 15 |
| Fixed deck over drawers | 3/4 | 1 | 40 x 15 |
| Outer sides, drawer section | 1/2 | 2 | 15 x 7 |
| Center divider | 3/4 | 1 | 14 1/2 x 7 |
| Bulkhead, drawers to bay | 1/2 | 1 | 39 x 7 |
| Floor battens, drawer section | 3/4 | 3 | 15 x 1 1/2 |
| Bay side walls | 1/2 | 2 | 14 1/4 x 8 1/4 |
| Bay rear wall | 1/2 | 1 | 39 x 7 1/2 |
| Hinge rail | 3/4 | 1 | 39 x 1 1/2 |
| Hinged lid | 3/4 | 1 | 39 3/4 x 14 1/8 |
| Drawer bottoms | 1/2 | 2 | 17 5/8 x 14 |
| Drawer sides | 1/2 | 4 | 14 x 5 1/2 |
| Drawer ends | 1/2 | 4 | 16 5/8 x 5 1/2 |
| Drawer faces | 3/4 | 2 | 19 7/8 x 8 |
About 59 lb of plywood by our arithmetic. Add a piano hinge the width of the lid, a lid stay or gas strut, and latches.
- Latch the lid. Fit a latch at the front edge, so it stays shut in a rollover or a hard stop. An unlatched lid lets everything in the bay out.
- Check the arc. A 14 in lid needs about 14 in of clear height above the deck, and a hardtop or cargo cover can get in the way. Mock up the swing with cardboard.
- Check the reach. You reach over the drawer section into the bay. Put the heavy items at the drawer end of the bay, and pull a drawer out to stand closer if your bumper allows. On a rig with a folding seat, you can also reach it from the back seat.
- Hold gear down inside. Add tie-down points in the bay, since it has no drawers to contain things.
Anchoring: the part you cannot skip
A loaded drawer box sits directly behind your passengers, so this section matters more than any joint. Crash forces are far higher than the load's weight. The seat standard uses 20 times the seat's mass as a forward load, and a European luggage test runs two 18 kg blocks at 20 g. Researchers found that test unrealistically light, and crash tests still wrecked seat backs.
By our arithmetic, a 200 lb loaded box at 20 g is about 4,000 lbf, treated as a static load. That is not a design standard. It is a sense of scale. We found no drawer-specific US standard, and we cannot tell you a home-built system is crash-safe.
- Never use wood screws or sheet metal screws into the floor. They have little thread engagement in thin sheet.
- Through-bolt with backing plates wherever you can see both sides, as Tuffy's TJ drawer does with four 7/16 x 1-1/4 in bolts through the floor. Look underneath first, and on an XJ especially.
- Reuse factory anchor holes as locating points, and verify the thread yourself. Owner reports vary: M6 on a JK, and M8-1.25 button heads on one JL rail install, which may not be the factory thread. A M6 tie-down was designed to hold a tie-down loop, not your whole system. Use several, and add a through-bolt if you can.
- Rivnuts are not magic. One reference gives about 510 lbf for a 1/4-20 in 0.030 in steel, and about 2,090 lbf in 0.125 in. Thin floor metal changes the answer.
- Do not bolt to seat belt anchors unless you know what that does to the belt. We found no source saying it is safe, though one owner has done it.
- Keep the load low and behind the seat back, and add a cargo barrier if you carry anything above it.
- Add up the weight. Read the door sticker for your payload, because published figures conflict: Quadratec lists 1,000 lb for 2007-11 JKs, and another of its pages cites 700 lb for a 2012 Rubicon. The box, the fridge, your gear and your passengers all count against it.
Step by step: build it yourself
These steps fit all four builds. Plan a weekend for the box, plus curing time for the finish. You can do this with a circular saw and a straightedge; a table saw makes it faster.
Tools
- Circular saw with a straightedge guide or track, or a table saw, with a fine-tooth plywood blade
- Drill, 1/8 in pilot bit, countersink, and bits sized to your T-nuts
- Tape measure, framing square, and clamps (at least four)
- Socket set, Torx or hex drivers to suit your screws, a torque wrench for floor bolts
- Jigsaw or chisel for lever notches and latch cut-outs. Add a router only if you want rounded edges
Shopping list
| Item | How many | Notes |
|---|---|---|
| Locking drawer slides (see above) | 1 pair per drawer | Length from your cut list |
| Baltic birch or void-free plywood | 1/2 in: one 4x8, or two 5x5 sheets. 3/4 in: one 4x4 | Reference builds use 16 to 31 sq ft of 1/2 in and 10 to 14 sq ft of 3/4 in, plus waste. Lay out Build B before buying, because one 4x8 is tight |
| M6 T-nuts and low-profile M6 x 16 mm screws | 6 per slide section, so 24 per drawer. Buy extra | Some slide kits include screws. Use a low head, so it clears the moving rail |
| Wood glue, water-resistant (type II or III) | 1 bottle | For all carcass and drawer joints |
| #8 x 1 1/4 in construction screws | 1 box | Panel joints only. Never into the Jeep |
| Key-locking paddle latch | 1 per drawer, optional | For security. The slide already holds the drawer shut |
| Spar varnish, polyurethane or paint | 1 quart | Seal every face and every cut edge |
| Grade 8 bolts, large washers, backing plates, angle brackets | At least 4 anchor points | Sized to your anchor plan. See the anchoring section |
| Foam weatherstrip, carpet or rubber mat | As needed | Quiets rattles and keeps gear from sliding |
| Piano hinge and folding lid stay | Build D only | The lid is about 9 lb by our arithmetic, so a stay is enough |
| Fridge slide, straps, 12 AWG wire, fuse | Build C only | See Build C |
Before you cut
- Check the floor. Pull the carpet or panel. Find any sub, the factory anchors, and what sits under the floor. On an XJ, look from underneath before you decide on any hole.
- Mock it up in cardboard. Build the box to size in your Jeep. Test the drawer fully open, seat recline, gate swing, and latch clearance. Check it passes through the opening, or plan to assemble it inside.
- Buy the slides, then finish your cut list. Use the formulas under Build B with your real slide length and thickness. Round the slide length down to a size you can buy.
Cut and seal
- Cut all panels. Cut the largest first, and cut matching parts with the same saw setting. Label each with tape. Cut drawer faces last, after the drawers fit.
- Test-fit dry, and check the carcass is square before any glue goes on.
Build the carcass
- Lay out the slide lines before assembly. It is far easier on flat panels. The rails are 3 in wide, so to center them, set the lower edge of each cabinet rail above the base panel at (opening height minus 3) divided by 2. That is 2 in for 6-inch drawers and 3 1/2 in for 9-inch drawers. Cut two spacer blocks to that height and rest each rail on them. Set the rail's front flush with the carcass front.
- Install the T-nuts and mount the cabinet rails. Separate each slide, drill through the rail's holes into the side panel, and seat T-nuts from the outside. On the center divider, offset the holes between its two faces so the T-nuts do not collide. Use every hole your slide offers. Keep both rails in a pair parallel: the SHUHANG listing warns that an out-of-parallel pair will be damaged.
- Assemble. Glue and screw the sides, divider and back to the base panel. Measure both diagonals: equal means square. Clamp and let it cure. Leave the deck off for now.
Build and hang the drawers
- Build the boxes. Glue and screw the sides to the ends, then glue and screw the bottom underneath. Check the diagonals. Each box should be 1 1/2 in narrower than its opening. On the box side, set the lower edge of the drawer rail above the box underside at the same spacer height minus 1/2 in: 1 1/2 in for 6-inch drawers and 3 in for 9-inch drawers. Mount with M6 screws into T-nuts inside the box, then cover with a 1/8 in liner if the nuts could snag gear. Hang the drawer and cycle it fully, empty and then loaded. If it binds, the rails are not parallel. Fix that now.
- Add the faces, with a lever notch. Find the lock lever with the drawer closed. Cut a notch or finger hole in the face so you can reach it, about 1 1/4 x 3/4 in as a starting point, then adjust it to your slide. If both slides in a pair have levers, plan to reach both, or use a wider finger slot along the bottom. Attach the face from inside with screws, with about a 1/8 in gap all around. Cut any latch opening now.
Finish the box
- Attach the battens under the base panel, running front to back, so the box clears floor ribs and stays level. Shim as needed. If you have a sub, cut the base and move the battens to clear it, or use Build D.
- Seal it. Remove the slides and faces if you can. Coat every surface and edge, with extra on the bottom. Let it cure fully before refitting.
- Fit the deck with screws you can remove later, so you can reach the slide fasteners. Cover it with carpet or a rubber mat, and add tie-down points. For a fridge on top, through-bolt its slide to a plate under the deck rather than into the deck alone.
Install and test
- Anchor it. Follow the anchoring section above, with at least four points, and torque the bolts. Do not skip this to try the drawers.
- Quiet it. Add weatherstrip where drawers meet stops, and check for rattles with the drawers empty.
- Test on a rough road, loaded. Check that drawers stay locked shut, hold open on a slope, and that nothing shifts. Keep heavy gear low and toward the seat.
- Re-check every bolt after the first trail run, and again after a month. Add a thread-locking compound to anything that moved.
Changes for Build D
- Build the drawer section as above, with the bulkhead replacing the back panel.
- Attach the bay side walls to the outer sides, and set the rear wall between them with the hinge rail on top.
- Fit the piano hinge to the rail and the lid's seat-side edge, then the lid stay. Add a latch at the front edge, and check the swing with the seat in place.
Common questions
Is it cheaper to build Jeep cargo drawers than to buy them?
Usually, going by owner estimates. JL and JK kits run from about $450 to about $2,500. On the XJ, building is the realistic option, because we found no current commercial kit.
Will a drawer fit over the factory JL subwoofer?
Only if it is built for it. The Alpine sub sits in the cargo floor. Some products have a sub version and some exclude it, so check the listing or build around it.
What drawer height should I build?
6-inch drawers keep the deck low at about 9 inches overall and leave room for a fridge on top. 9-inch drawers bring the deck to about 12 inches and hold tall items, but make a top-mounted fridge impractical on an XJ.
Dimensions, fit and owner reviews come mainly from listings and owner forums, and several forum sources could only be read as search excerpts. Measurements conflict, so we show them as starting points. We did not build each of these on each Jeep. We did not find reliable numbers for the JL's tie-down thread, its exact sub size, its seat fold angle, or a 2-door's seat-up depth, so measure those yourself. Cut-list dimensions are computed for the reference boxes shown.
Sources
Every source this guide draws on, grouped by site. Owner measurements and reviews are one person's report. Forum sources were mostly read as search excerpts. Prices and ratings were read October 30, 2026.
- 2011+ slide works with the sub (altapac.com)
- SHUHANG 76mm locking slides, Amazon listing (specs, price and rating read October 30, 2026) (amazon.com)
- VEVOR 24 in single-lock slides, Amazon listing (specs, price and rating read October 30, 2026) (amazon.com)
- SLIDEWAY 76mm locking slides, Amazon listing (specs, price and rating read October 30, 2026) (amazon.com)
- American Adventure Lab M.A.S.S. (americanadventurelab.com)
- Accuride 3832 (cabinetparts.com)
- Fulterer FR5000 (cabinetparts.com)
- Fulterer 5600L / 5609L (cabinetparts.com)
- Rough Country 99030 (completewebsol.com)
- ICECO JP42 (device.report)
- two 18 kg blocks at 20 g (digitallibrary.un.org)
- Dometic CFX3 45 (dometic.com)
- Dometic CFX3-SLD3545 (dometic.com)
- Dometic CFX3 55IM (dometic.com)
- about 510 lbf for a 1/4-20 in 0.030 in steel, and about 2,090 lbf in 0.125 in (eugenefast.com)
- ARB Roller Drawer RDK5013020 (extremeterrain.com)
- Smittybilt 2763 (also JK) (extremeterrain.com)
- a 1 in lip that calls for a riser (extremeterrain.com)
- 4.8 from 4 reviews (extremeterrain.com)
- Rugged Ridge lists it (extremeterrain.com)
- SquadBox J257997 (extremeterrain.com)
- four 7/16 x 1-1/4 in bolts through the floor (extremeterrain.com)
- spar varnish on 1/2 in birch (forum.expeditionportal.com)
- Owners call it well built (forum.expeditionportal.com)
- ARB RDRF790 is 105.8 lb (forum.ih8mud.com)
- 20 times the seat's mass as a forward load (gpo.gov)
- 12 AWG for a DIY circuit to a CFX3 45 (gwagenparts.com)
- 12 to 18 in deep with the seat up (jkowners.com)
- Hooke Road drawer and fridge mount (also JK) (jlwranglerforums.com)
- A 10 in sub in the cargo floor (jlwranglerforums.com)
- the connector is behind the passenger-side plastics (jlwranglerforums.com)
- reported fine by one owner (jlwranglerforums.com)
- cargo volume drops to 67.4 cu ft folded (jlwranglerforums.com)
- Solid and smooth, heavier than expected (jlwranglerforums.com)
- One owner: the floor pulls open with the drawer locked (jlwranglerforums.com)
- About 29.5 to 30 in seat to door at sill height (jlwranglerforums.com)
- a shallow floor tub (jlwranglerforums.com)
- the folded seat as a ledge about 7 in above the floor (jlwranglerforums.com)
- 34.5 in seat base to gate (jlwranglerforums.com)
- M8-1.25 button heads on one JL rail install (jlwranglerforums.com)
- 44 to 48 in deep with the seat out (jlwranglerforums.com)
- an owner reports a CFX3 45 slide barely fits (jlwranglerforums.com)
- a forum seller offers CNC-cut kits for $270 to $390 (jlwranglerforums.com)
- it holds the tuning and volume control (jlwranglerforums.com)
- 43 in between wells, 34 1/2 in long at the floor (naxja.org)
- The Infinity amp (naxja.org)
- a full-width box means moving it (naxja.org)
- 48 x 32.75 in opening (naxja.org)
- frame rails, the plastic fuel tank, filler hoses and shackle mounts (naxja.org)
- 130-01 underseat drawer (northridge4x4.com)
- 13 in Tuffy 131-01 (northridge4x4.com)
- cargo barrier (nrspp.org.au)
- ICECO VL45 (offgridstores.com)
- Front Runner kit is 42.8 x 28.4 x 10.6 (offroadtents.com)
- Goose Gear 2-door plate (overlandkitted.com)
- a separate 392 plate, with sub only (overlandkitted.com)
- a narrower module on the sub side (overlandkitted.com)
- DECKED SUV drawer (also JK) (pickuptrucktalk.com)
- 44.7 in between wells (quadratec.com)
- needs a JKBRKT1 bracket on 2007-09 rigs with the sub (quadratec.com)
- 45 in between wells, 41.1 in gate opening (quadratec.com)
- 700 lb for a 2012 Rubicon (quadratec.com)
- 1,000 lb for 2007-11 JKs (quadratec.com)
- TACTIK box (also JK) (quadratec.com)
- JCR XJ Cubby Mate (quadratec.com)
- In the center console (quadratec.com)
- Tuffy excludes it (quadratec.com)
- Tuffy Security Drawer #140 (quadratec.com)
- Tuffy 058-01 is 35 3/8 x 30 x 8 (quadratec.com)
- Tuffy 131-01 is 34 x 20 1/4 x 13 (quadratec.com)
- Accuride 9308E (reiman.pt)
- reported as hard to find (sawmillcreek.org)
- unrealistically light, and crash tests still wrecked seat backs (sjtrem.biomedcentral.com)
- about 50 mm of ventilation clearance (solartown.com)
- non-locking (64-21-10) and key-locking (64-22-10) in stainless (southco.com)
- ARB 10900021, 176.4 lb (store.arbusa.com)
- the value varies (support.dometic.com)
- under-seat subs such as the Alpine PWE-S8-WRA (volunteeraudio.com)
- wheel wells about 11 to 12.5 in tall (wranglerforum.com)
- M6x1.0 on a 2014 JKU (wranglerforum.com)
- About 36 x 36 in floor (wranglerforum.com)
- about 20 minutes with star bolts (wranglerforum.com)
- 37.5 to 42 in wide, by owner (wranglerforum.com)
- 43 in between fenders but 36.5 in at the factory sub (wranglerforum.com)
- 34.25 to 34.5 in with brackets (wranglertjforum.com)
- rattles and water leaks (wranglertjforum.com)